SinceVision Launches SGI-N030W Wide-Spot Laser Displacement Sensor

New wide-spot sensor targets stable micrometre-level measurement on rough and coated surfaces in battery, semiconductor and precision assembly work.

SinceVision has introduced the SGI-N030W, a wide-spot laser displacement sensor aimed at high-speed, non-contact dimensional measurement of rough, textured and irregular surfaces. The company describes the model as an addition to its SGI Series laser displacement sensor range, targeting lithium-ion battery manufacturing, semiconductor processing and precision mechanical engineering, where reliable micrometre-level measurement is required.

The design responds to a known limitation of conventional point-spot laser displacement sensors, which concentrate reflected laser energy onto a small area. On such systems, microscopic surface features — scratches, grain boundaries, brushed textures and matte finishes — can introduce signal variations that are interpreted as dimensional changes, potentially triggering false defect warnings and additional inspection.

Wide-spot optical configuration

The SGI-N030W instead collects reflected light across a broader surface area. According to SinceVision, this effectively averages localised microscopic peaks and valleys before signal conversion, reducing the influence of surface roughness and optical scattering. The company cites drawn metals, sandblasted surfaces and coated battery foils as materials on which the approach is intended to provide more stable displacement readings.

Specifications

The sensor has a reference distance of 30 mm and a measurement range of ±5 mm. SinceVision specifies repeatability of 0.05 µm on a diffuse white target under static conditions, with linearity of ±0.02% of full scale across the range. A sampling frequency of 50 kHz, equivalent to a 20 µs update interval, is intended to support high-speed measurement and monitoring of dynamic processes.

Communication options include RS485, 100Base-TX Ethernet and switchable analogue outputs carrying either 4–20 mA current or 0–10 V voltage signals. The system also provides master-slave synchronisation, allowing two sensors to operate in opposition and measure simultaneously from either side of a component or moving material.

In-line thickness measurement for battery production

One of the principal applications identified by SinceVision is in-line thickness measurement of lithium-ion battery electrodes, where coating thickness and uniformity influence energy density, internal resistance and long-term cell stability. The company notes that offline inspection using contact micrometers or drop indicators can introduce operator variability and may deform wet or uncured electrode material, while periodic spot measurements cannot provide continuous coverage across an entire production reel.

In the proposed arrangement, two synchronised sensors are positioned above and below a moving electrode web on a calibrated, low-thermal-expansion marble gantry. The opposing heads measure their respective clearances to the material, and a system controller combines these readings with the fixed mounting datum to calculate absolute thickness in real time. SinceVision reports that production trials demonstrated stable, repeatable thickness measurement within ±0.3 µm at a web speed of 300 mm/s. The company says the 50 kHz sampling rate provides high longitudinal resolution, enabling detection of localised coating agglomerations, edge thinning and exposed substrate before the material proceeds to cell winding.

Semiconductor and precision assembly uses

The sensor is also intended for semiconductor manufacturing, where non-contact measurement matters when handling sensitive wafer surfaces. Potential applications listed by the company include wafer position verification, edge detection, height measurement, and checks of wafer seating and chuck alignment in atmospheric transfer modules and vacuum load-lock systems.

In precision assembly, the sensor can monitor the movement of voice coil motors, linear actuators and micro-steppers. Its 50 kHz sampling rate is intended to capture transient displacement, mechanical oscillations, settling behaviour and end-stop overshoot across the full measurement range, with position data sent to machine control systems through the Ethernet interface.

Addressing surface-related errors

Jack Li, Global Sales and Marketing Director at SinceVision, said false defect warnings caused by surface texture remain a recurring challenge in battery manufacturing and precision assembly. He said conventional point-beam laser sensors can interpret microscopic scratches and rough coatings as actual thickness variations, slowing production lines and creating a need for extra manual inspection. The company states that the SGI-N030W’s expanded optical spot is designed to average out these surface-related variations, while synchronisation between opposing sensor heads supports high-speed thickness verification.

LP

Lucian Petrescu

Lucian Petrescu is an editorial analyst covering RF connectors, coaxial and fiber cable assemblies, antennas, and passive components for carrier and enterprise telecom infrastructure. His articles examine VSWR as a ratio, passive intermodulation in dBc, insertion and return loss in dB, connector mating limits, and cable bend radius, always scoped to applicable IEC test methods and stated measurement setups. He helps RF design engineers, installation teams, system integrators, and technical procurement groups compare interconnect options, request traceable measurements, and plan deployments without treating any product as certified.